Ghost Immobiliser Fitting
Secure your vehicle from theft of keys, cloning and hacking with the world's first aftermarket CAN immobiliser. With the option of connecting to a Ghost app and GPS tracking system that can send you alerts to call if your car is tampered with or stolen.
Installing an Ghost immobiliser is a breeze for the qualified technician. It is essential to have the appropriate tools and heat shrink tubing.
Getting Started
Contrary to physical theft protection devices like wheel locks or car alarms, ghost immobilisers safeguard your vehicle without the need for LED indications or key fobs. Instead they connect directly to the ECU's CAN data network. They will only start after entering a PIN code sequence. This offers a higher level of protection against key hacking, ECU swapping and cloning.
As a result, installing a ghost immobiliser Birmingham is a task that must be carried out with a high degree of agility and precision. It can be a bit like tiptoeing through an icy minefield. One mistake can cause serious damage to the circuits of the electrical system of your vehicle. To avoid this, it's essential to be aware of the process of installation and prepare your vehicle appropriately.
You'll need to take out interior panels from the vehicle in order to make room for your immobiliser. Once you have found the perfect location to conceal it, use cable tie to ensure it is secured. Clean up your wiring by connecting loose wires and using insulation tape to cover exposed connections. This reduces the risk of a short circuit that is not intended to happen, while improving the aesthetics and reducing the chance of theft.
Find a reliable source of 12V power, and a grounding source for the ghost immobiliser. Once you've found these, test the power wires with a multimeter to make sure they're delivering the same voltage. Connect the CAN H and CAN L wires from the immobiliser to your chosen power source and grounding point.
Once you've made all of the necessary connections It is important to check them and inspect the immobiliser for indications of corrosion or damage. Also, test the system to ensure it is working properly by entering a PIN number and then starting the engine. This should be an ongoing part of your routine, because it will allow you to detect any issues that might be intermittent early. Regular testing will also help to prolong the life of the device and keep it running at its peak performance.
Preparing the vehicle
Installing a Ghost immobiliser requires knowledge and tools. A wiring diagram of the vehicle is essential for locating the correct wires and establishing precise connections. A multimeter can be used to verify the electrical properties and ensure safety. Insulation tape and cable ties can be used to protect the connections from damage and keep them secured. A user's manual is available for your Ghost Immobiliser. It will give you specific instructions tailored to that model.
Once installed, the ghost immobiliser will stop engine starts that are not authorized by requiring the owner to input a unique code sequence using the buttons on the steering wheel or console. This can be accomplished manually or remotely using a mobile phone app, and the code is able to be altered by the owner of the vehicle at any time. The device is silent and is undetectable by thieves as it does not emit any radio frequency.
Ghost immobilisers are directly connected to the CAN bus of the vehicle, which is a network that communicates with the electronic control units (ECUs) of the vehicle. It intercepts signals generated by the ECUs and prevents the engine from starting if it detects a false signal. The system is tamper-proof and weatherproof, and does not include key fobs or LED indicators to draw the attention of thieves.
It can be positioned behind the dashboard or in an inconspicuous area, so it isn't visible to thieves and doesn't hinder the performance of the vehicle. It can be placed in a small container so that it is less likely to be spotted by fraudulent salespeople when they test drive.
Its low-profile operation and integration with the vehicle's CAN bus network make it a powerful deterrent to the latest methods of car theft, like key cloning and signal relay attacks. The system can be combined with other security measures to create a powerful barrier that will frustrate even the most obstinate thieves. This is the reason why more insurance companies are suggesting or even requiring ghost immobilisers to be fitted, as it will significantly lower the cost of insurance.
Making the Connections
In contrast to traditional security systems that are heard by thieves, ghost immobilisers work silently to keep them from being aware that your vehicle has been switched on. They also stop high-tech methods employed to steal vehicles, such as OBD port hacking. Installing them without leaving permanent marks on your car is an excellent alternative for those planning to sell the car in the near future.
The Autowatch Ghost 2 is a CANbus immobiliser that is among the most reliable and modern solutions to prevent car theft. It utilizes the CAN data network to disable your engine and generates a PIN code that only you know, meaning it's difficult for criminals to detect. It can be used on a wide range of automobiles, and it can work with a variety of features already installed including car alarms and steering wheel locks. GPS trackers, and door lock bypass.
If you opt to use a Ghost immobiliser for your vehicle, make sure to consult the wiring schematic to identify the wires to connect. Verify the location of these wires to ensure accuracy and mark them with tape or labels to make it easier to keep the track of them. You'll also need to locate a consistent power source (12V) for the system, as well as a grounding. Once you have these in place, you are able to begin to make the connections needed to complete the installation.
The ghost immobiliser won't allow your vehicle to start unless the pin code is entered through the buttons of the steering wheel or dashboard. This will stop ECU hacking or key cloning and other methods of theft. Additionally, it can be combined with other Thatcham-approved security devices, like alarms and tyre clamps, to provide your vehicle with an additional level of protection.
As the UK automotive industry continues to expand, as do the options available for protecting your vehicle. With so many ways for thieves to get in and steal your car, it's vital to take every precaution to protect it from being taken away. Ghost immobilisers are an increasingly popular option for car owners who are responsible.
Testing the System
The Ghost Immobiliser communicates with the vehicle's ECU via a CAN network. This prevents the engine from starting until the PIN code has been entered. This makes it difficult for thieves to steal your key fob to start your vehicle, and harder to disable the system through hacking its electronics.
Ghost Immobilisers can also be used with GPS tracking devices to help you locate your vehicle in the event that it's stolen. This is a feature that isn't often found in aftermarket security products however it is an excellent way to improve your vehicle's security and provide you with peace of peace of.
In addition to offering enhanced security and security, the Ghost-II immobiliser offers a convenient user experience by removing the need for additional key fobs and devices. It is simple and easy PIN code entry system that works seamlessly with your everyday routine. It also offers options for deactivation and features that allow you to temporarily disable the immobiliser to allow valet parking or servicing.
Before you begin the installation process, you should familiarise yourself with your vehicle's wiring and prepare the required tools. A basic set of hand tools will give you the flexibility to create precise connections, while a multimeter can help determine electrical values. Insulation tape and heat shrink tubing are crucial for securing connections from short circuits, while cable tie is a great way to keep the wiring in place. Additionally, it is essential to be in a well-lit space and wear appropriate safety gear when working with electrical and tool components.
After you've completed the installation you should test the Ghost immobiliser to verify that it's working as intended. You should first try to start the car without entering the PIN. If this fails then you'll need to try again and check the connections more carefully.
In contrast to other security systems that are available, unlike other security systems, the Ghost Immobiliser is a covert device that is not spotted by thieves and is much more effective than traditional deterrents such as wheel clamps or steering locks. cost of ghost immobiliser The Keylab is TASSA-approved and endorsed by a few insurance companies. This makes it a cost-effective investment that will give you the peace of heart you deserve.